No products
Used with photogrammetry for targeting holes approximately 90° to line of sight. T90 FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard) NOTE: Target dots are located within +/-.0005 on height ...
Used to target above and 90° to steel surfaces. The side of the body may be used to target surfaces, edges, or steps .2500 or .3750 away.TM FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)TM OR...
Used with photogrammetry for targeting holes approximately 45° to the line of sight.T45 FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on hei...
Used to target above and 90° to steel surfaces when a 45° target face is more applicable. The side of the body may be used to target surfaces, edges, or steps .2500 away.T45M FEATURES: 1144 ST...
Used with photogrammetry for targeting edges/surfaces.TC / 45 - LH or RH FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless otherwi...
Used with photogrammetry for targeting edges/surfaces.TC / 45 NEG or POS FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless o...
Used with photo- grammetry for targeting .125 diameter tooling holes. For any other requirements, refer to TBRV design.TB FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)TB ORDERING: Can only selec...
Used with photogrammetry for targeting .125 diameter tooling holes.TBR FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless otherwise...
Used with photogrammetry to measure location and angularity of a hole.NOTE: .2500 maximum dot diameter. For larger dot diameters, use DVTV.DVT FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE:&...
Used with photogrammetry to measure location an angularity of a hole.DVTV FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless otherw...
Used with photogrammetry to target edges/surfaces.DTET FEATURES: 1018 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless otherwise noted) or +/-.0...
Used with photogrammetry to measure location an angularity of a hole.45 DVT FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless othe...
Used with photogrammetry for targeting edges/surfaces.TC / 90 LH or RH FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless otherwise...
Used with photogrammetry for targeting edges/surfaces.TC / 90 NEG or POS FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless otherwi...
Designed for use with photogrammetry where radial location is desired.NOTE:Ball Diameter --- Largest Dot.500" --- .250" (6mm)1.000" --- .500" (12mm)1.500" ---...
Used with photogrammetry for locating edges of sheet metal, slots or grooves.NOTE: The side of the target with the flat represents the side of the indexing surface.TSG FEATURES: 1144 STEEL, BLACK OXID...
Provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interghangeability from Laser Tracker systems to Photogrammetry or Videogrammetry systems.1.5S FEATURES: HARDENED S...
Provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interchangeability from Laser Tracker systems to Contrast Photogrammetry or Videogrammetry systems.1.5S FEATURES:&n...