Skip Navigation

Best sellers

Showing 1 - 155 of 155 items
  • $28.50

    Used for establishing non-critical temporary or permanent monuments using hot-glue or permanent adhesives.1.5 SM - DN - 3PA FEATURES: ALUMINUM BLACK, HARD ANODIZED COATING• Low cost• Lightwe...

    $28.50
  • $143.00

    Designed to hold a .5 Spherically Mounted Retro-Reflector or other spherical type target or accessory on centerline of a threaded hole and critical offset.NOTE: M8 or 5/16 thread are the sma...

    $143.00
  • $28.50

    Used for establishing non-critical temporary or permanent monuments using adhesives or by tack welding.NOTE: We suggest removing the magnet before welding.1.5 SM - DN - 3PS FEATURES: 1144 STEEL, BLACK...

    $28.50
  • $35.00

    Designed to hold .5000 Spherically Mounted Retro-Reflector or other spherical type target or accessory as a temporary reference point.NOTE: To Use: Hold .5 Reflector Holder Drift Nest in pla...

    $35.00
  • $41.00
    Sale!

    Used with photogrammetry for targeting holes approximately in line with line of sight.TSO FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)TSO ORDERING: Normal offsets for targets are:.3125.5001.000...

    $41.00
  • $28.50

    Sometimes called a “hockey puck,” the 1.5 SM-TM provides a temporary magnetic SMR adaptor in almost any location on any surface by using hot glue to attach the adaptor temporarily.1.5 SM -...

    $28.50
  • $35.50

    Used for establishing non-critical temporary or permanent monuments using hot-glue or permanent adhesives, and allows for rotation below horizontal.1.5 SMN - DN - 3PA FEATURES: ALUMINUM BLACK, HARD AN...

    $35.50
  • $92.50

    Designed to hold a .5000 Spherically Mounted Retro-Reflector or other spherical type target or accessory on centerline of a hole and critical offset.NOTE: For a .3125 offset only, the minimu...

    $92.50
  • $72.75
    Sale!

    Supports .5000 Spherically Mounted Retro-Reflector or other spherical type target or accessory for critical offset and centerline. The edge may be used to contact in edges to a value of .250...

    $72.75
  • $13.75

    Used with photo- grammetry for targeting .125 diameter tooling holes. For any other requirements, refer to TBRV design.TB FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)TB ORDERING: Can only selec...

    $13.75
  • $17.50

    Low-cost, efficient way for establishing a permanent, critical .2500 diameter target hole along with a flat and perpendicular reference upper surface. Epoxy, hot glue, or tack weld in place.TRP FEATUR...

    $17.50
  • $75.00

    Used with photogrammetry for targeting holes approximately 45° to the line of sight.T45 FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on hei...

    $75.00
  • $131.00

    Designed for use with photogrammetry where radial location is desired.NOTE:Ball Diameter --- Largest Dot.500" --- .250" (6mm)1.000" --- .500" (12mm)1.500" ---...

    $131.00
  • $65.00

    Used with photogrammetry for targeting holes approximately 90° to line of sight. T90 FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard) NOTE: Target dots are located within +/-.0005 on height ...

    $65.00
  • $35.50

    Used for establishing non-critical temporary or permanent monuments using adhesives or by tack welding, and allows for rotation below horizontal.NOTE: We suggest removing the magnet before welding.1.5...

    $35.50
  • $92.50

    Allows SMR rotation below horizontal..5 SMN FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)STAINLESS STEEL OPTION (for more corrosive environments)SM is a Registered Trademark of Hubbs Machine &am...

    $92.50
  • $157.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of a hole and 1.000 above or optional 2...

    $157.00
  • $138.00

    $138.00
  • $139.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory as a permanent reference point.1.5 LT - RSM FEATURES:...

    $139.00
  • $72.75

    Allows SMR rotation below horizontal..5 SSMN FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)STAINLESS STEEL OPTION (for more corrosive environments)SM is a Registered Trademark of Hubbs Machine &a...

    $72.75
  • $32.00

    Uses .2500 + .0003 / .0000hole that is perpendicular to the top surface which allows interchangeability with standard construction ball, standard optical targeting, or larger diameter items such as La...

    $32.00
  • $189.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of a threaded hole and 1.000 above or&n...

    $189.00
  • $31.50

    Used for establishing non-critical temporary or permanent monuments using hot-glue or permanent adhesives or it can be bolted on.

    $31.50
  • $134.00

    Mounted in concrete flooring/foundations, etc., to allow for a permanent 1.5 spherical target reference.1.5 FSM FEATURES: STAINLESS STEEL (standard)SM is a Registered Trademark of Hubbs Machine & ...

    $134.00
  • $157.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of a hole and 1.000 above or 25mm above.1.5 ...

    $157.00
  • $94.00

    Used for adapting standard .2500 or .1250 shank targets to odd-sized holes. (Allow .2000 for height difference) Many nominal fractional sizes in stock.NOTE: For head diameter, add .37 to

    $94.00
  • $129.00
    Sale!

    Intended to be used when standard, off the shelf designs, such as .3125 and .5000 offsets with .2500 shanks, cannot be used. All of are balls are welded to the shank.These two common sizes are $50.00:...

    $129.00
  • $40.00

    $40.00
  • $64.00

    Mounted in concrete flooring/foundations, etc., to allow for a permanent reference.FTI FEATURES: MEDIUM KNURLED BRASS...

    $64.00
  • $90.00

    Designed to adapt 90° standard .2500 shank targets to an Invar Scale Bar Kit.ITA FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)...

    $90.00
  • $192.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of a hole and 1.000 above or 25mm above...

    $192.00
  • $72.50

    Designed for mounting to a surface to securely hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory. The 1.5SM-H...

    $72.50
  • $1,025.00

    Hubbs Machine & Manufacturing distributes PLX ball mounted retro reflectors (BMR's). They are manufactured with the apex of the retro reflector aligned with the absolute center of the steel ball w...

    $1,025.00
  • $198.00

    Designed for adhering to a steel surface to securely hold a Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target ...

    $198.00
  • $76.00

    Designed to hold .5000 Spherically Mounted Retro-Reflector or other spherical type target or accessory as a permanent reference point..5 LT - RSM FEATURES: 1144 STEEL OXIDE FINISH (sta...

    $76.00
  • $135.00

    The Precision Scan Sphere provides the same centerline value as a 1.500” Spherically Mounted Retro-Reflector. This allows interchangeability of targeting from Laser Tracker systems to Laser Scan...

    $135.00
  • $57.00

    Designed to locate the center of a scribed cross-hair using tick marks.MBTHA FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)...

    $57.00
  • $60.00

    Designed to hold a sphere directly on the surface.FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)SM is a Registered Trademark of Hubbs Machine & Manufacturing Inc....

    $60.00
  • $253.00

    NOTE: 10 or more rolls of the same size are eligible for quantity discount. Call for discounted rates. Retro-Reflective tapes are sold in rolls that are 50 yards long....

    $253.00
  • $1,275.00

    Hubbs Machine & Manufacturing distributes PLX ball mounted retro reflectors (BMR's). They are manufactured with the apex of the retro reflector aligned with the absolute center of the steel ball w...

    $1,275.00
  • $76.00
    Sale!

    Used to target above and 90° to steel surfaces. The side of the body may be used to target surfaces, edges, or steps .2500 or .3750 away.T90M FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)T90...

    $76.00
  • $157.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for a critical height and centerline. The edge may be...

    $157.00
  • $105.00

    Designed to hold a .5000 Spherically Mounted Retro-Reflector or other spherical type target or accessory to target edges/surfaces.NOTE: 10mm shortest offest on .5 SM/TC.5 SM / TC FEATURES: 1...

    $105.00
  • $164.00

    Used with photogrammetry to measure location an angularity of a hole.45 DVT FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless othe...

    $164.00
  • $134.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of a hole and 1.000 above or 25mm above...

    $134.00
  • $117.00

    Designed to hold a .875 Spherically Mounted Retro-Reflector or other spherical type target or accessory on centerline of a hole and critical offset.NOTE: The “H” offset must be .500 minimu...

    $117.00
  • $85.00

    Designed to hold a CMM Probe tip on centerline of a hole and critical offset.PR / TSO FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)...

    $85.00
  • $75.00

    Used to target above and 90° to steel surfaces. The side of the body may be used to target surfaces, edges, or steps .2500 or .3750 away.TM FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)TM OR...

    $75.00
  • $105.00

    Designed to hold .5000 Spherically Mounted Retro-Reflector or other spherical type target or accessory during use.NOTE: HEAVY DUTY best for holding .5 SMR when profiling surfaces.HEAVY DUTY ...

    $105.00
  • $130.00

    Mounted in concrete flooring/foundations, etc. to allow for a permanent Laser Tracker target reference..5 FSM FEATURES: STAINLESS STEEL (standard)SM is a Registered Trademark of Hubbs Machine & Ma...

    $130.00
  • $113.00

    Adapts to a Theodolite Adaptor to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory in place for a consistant ...

    $113.00
  • $97.50

    Designed for mounting to a surface to securely hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory. The 1.5SM-HC/MB is use...

    $97.50
  • $527.00

    Provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interghangeability from Laser Tracker systems to Photogrammetry or Videogrammetry systems.1.5S FEATURES: HARDENED S...

    $527.00
  • $275.00

    Holds (2) Tooling Ball Retro-Reflectors or other spherical type target or accessory to measure location and angularity of a hole.DVT / SMLR FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)STAI...

    $275.00
  • $85.00

    Designed to hold a CMM Probe tip on centerline of a hole and zero offset.NOTE: Some probe tips and small shank diameters combinations have limitations.PR / FM FEATURES: 1144 STEEL, BLACK OXI...

    $85.00
  • $225.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for a critical height and centerline. The edge may be...

    $225.00
  • $170.00

    Designed to hold a .5000 Spherically Mounted Retro-Reflector or other spherical type target or accessory on centerline of a hole and critical offset when a non-magnetic mount is preferred..5...

    $170.00
  • $135.00

    Used with photogrammetry to measure location and angularity of a hole.NOTE: .2500 maximum dot diameter. For larger dot diameters, use DVTV.DVT FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE:&...

    $135.00
  • $54.00

    Used to adapt to a Hidden Point Bar or Bar Extensions to contact surfaces or scribe lines that are hidden from view.HP FEATURES: 1144 STEEL, BLACK OXIDE FINISH - Hardened to R/C 53-55 (sta...

    $54.00
  • $93.50
    Sale!

    Used for adapting standard .2500 or .1250 shank targets to standard type slotted bushings. (Allow .1875 for height difference)NOTE: .1250 hole when “A” dimension (flats) is less than .3120...

    $93.50
  • $112.00

    $112.00
  • $35.00

    Snaps on .5 SM for added protection of keeping the sphere from falling out.NOTE: Model 1 fits .3125'' or 10mm offsetModel 2 fits 12mm or .3000'' or higher offset.5 TBR RETAINER FEATURES: Allows free r...

    $35.00
  • $130.00

    Used with a Hidden Point Bar to extend lengths.BEX APPLICATION: shank end accepts Hard Point, Construction Ball Adaptor, 90 degree Adaptor, and Sphere Fit Adaptor or screw together with a Hidden Point...

    $130.00
  • $290.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating edges/surfaces.1.5 ESM - ...

    $290.00
  • $250.00

    The Super Precision Scan Sphere (SPSS) provides the same centerline value as a 1.500” Spherically Mounted Retro-Reflector. The SPSS fits over any 1.5 spherical item to hold the same center within .002”, including a SMR. Diameter held to within .002”. A 1.500 sphere is included with every SPSS. This allows interchangeability of targeting...

    $250.00
  • $83.00

    Used to target above and 90° to steel surfaces when a 45° target face is more applicable. The side of the body may be used to target surfaces, edges, or steps .2500 away.T45M FEATURES: 1144 ST...

    $83.00
  • $1,700.00

    Hubbs Machine & Manufacturing distributes PLX ball mounted retro reflectors (BMR's). They are manufactured with the apex of the retro reflector aligned with the absolute center of the steel ball w...

    $1,700.00
  • $372.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for a critical height and centerline. The edge may be...

    $372.00
  • $219.00

    NOTE: 10 or more rolls of the same size are eligible for quantity discount. Call for discounted rates. Retro-Reflective tapes are sold in rolls that are 50 yards long....

    $219.00
  • $253.00

    NOTE: 10 or more rolls of the same size are eligible for quantity discount. Call for discounted rates. Retro-Reflective tapes are sold in rolls that are 50 yards long....

    $253.00
  • $159.00

    Designed to adapt a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory to a customer-supplied pole extension (painting...

    $159.00
  • $395.00

    Adapts a Retro-Probe tip to centerline of 1.5000 Sphere to within .00025.NOTE: Nest for probe tip diameter from 1mm to .25001.5 RRS (BALL) FEATURES: STAINLESS STEEL BALL with 17-4 stainless steel inse...

    $395.00
  • $527.00

    Provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interchangeability from Laser Tracker systems to computer-aided Theodolite systems.T1.5S FEATURES: HARDENED STAINLE...

    $527.00
  • $402.00

    NOTE: 10 or more rolls of the same size are eligible for quantity discount. Call for discounted rates. Retro-Reflective tapes are sold in rolls that are 50 yards long....

    $402.00
  • $398.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating edges/surfaces. The 1.5ES...

    $398.00
  • $140.00

    FOR SPHERE FIT ROUTINES ONLYSFX APPLICATION: shank end accepts Hard Point, Construction Ball Adaptor, 90 degree Adaptor, and Sphere Fit Adaptor....

    $140.00
  • $337.50

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating edges/surfaces.1.5 ESM - ...

    $337.50
  • $190.00

    Used for adapting Invar Bar to flat steel surface.IMBA FEATURES: 1144 STEEL, BLACK OXIDE FINISH - Hardened to R/C 53-55 (standard)...

    $190.00
  • $527.00

    Provides same centerline value as a Spherically Mounted RetroReflector. This allows interchangeability from Laser Tracker systems to Total Station systems.TOTAL 1.5S FEATURES:...

    $527.00
  • $134.00

    Designed to locate a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of a hole when a magnet is not d...

    $134.00
  • $325.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating outside corners.1.5 ESM -...

    $325.00
  • $26.00

    Used for establishing non-critical temporary or permanent monuments using hot-glue or permanent adhesives .8755 SM - DN - 3PA FEATURES: ALUMINUM BLACK, HARD ANODIZED COATING• Low cost• Lightwe...

    $26.00
  • $132.50

    Used to adapt standard .2500 shank targets to edges/surfaces magnetically.MCA FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)...

    $132.50
  • $372.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for a critical height and centerline. The edge ...

    $372.00
  • $165.00

    Designed to tether a 1.5 Spherically Mounted Retro-Reflector to the user or Sphere Mount, preventing loss or damage.NOTE: Full set shown at left,drawings show included items in full or partial set.SMR...

    $165.00
  • $1,110.00

    Hubbs Machine & Manufacturing distributes PLX ball mounted retro reflectors (BMR's). They are manufactured with the apex of the retro reflector aligned with the absolute center of the steel ball w...

    $1,110.00
  • $192.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for a critical height and centerline. The edge may be...

    $192.00
  • $475.00

    Designed to find centerline of various diameters.DVTPM FEATURES: ALUMINUM BLACK, ANODIZED COATING...

    $475.00
  • $0.00
    Sale!

    Used with photogrammetry for targeting edges/surfaces.TC FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless otherwise noted) or +/-...

    $0.00
  • $450.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating center punch marks withou...

    $450.00
  • $365.00

    Designed to adapt a 1.5 Sphere Mount Nest to .5000 Spherically Mounted Retro-Reflector.1.5 - .5 SMR AD FEATURES: STAINLESS STEEL Heat-treated and hardened to R/C 53 - 55 (standard)...

    $365.00
  • $330.00

    Accepts a target or a sphere mount .500 high, .2500 shank, or .1250 shank in each end to achieve a 3.000 inch offset in each direction. For anything other than a 2.500 length in both directions, pleas...

    $330.00
  • $625.00

    Allows the SMR to be tracked into a position. A light tap with a hammer will produce a small accuratedly located center punch mark under the SMR location without removing the SMR. Item intended for la...

    $625.00
  • $165.00

    Designed to tether a 1.5 Spherically Mounted Retro-Reflector to the user or Sphere Mount, preventing loss or damage.NOTE: Full set shown at left, drawings show included items in full or partial set.LE...

    $165.00
  • $104.00

    Designed to adapt .2500 shank targets to the edge/surface of sheet metal.SETA FEATURES: Aluminum Black Anodized (standard)• Screw clamp will open to excess of 9/16”...

    $104.00
  • $77.00

    Holds a Hard Point 90° for locating to identifier rivets, scribe lines, etc.HPS FEATURES: ALUMINUM BLACK,ANODIZED COATING...

    $77.00
  • $134.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of a hole and 1.000 above or 25mm above...

    $134.00
  • $395.00

    Adapts A Retro-Probe tip to centerline of 1.5000 Sphere to within .00025.NOTE: Nest for probe tip diameter from 1mm to .25001.5 RRS (BALL FEATURES: STAINLESS STEEL BALL with 17-4 stainless steel inser...

    $395.00
  • $149.00

    Used with photogrammetry to measure location an angularity of a hole.DVTV FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless otherw...

    $149.00
  • $52.00
    Sale!

    Screws onto the end of a Bar Extension similiar to a Hard Point and allows the user to locate the conical nest around a construction ball in order to generate a sphere fit routine.SFA FEATURES: 1144 S...

    $52.00
  • $155.00

    Designed to tether a 1.5 Spherically Mounted Retro-Reflector to the user or Sphere Mount, preventing loss or damage.NOTE: Full set shown at left, drawings show included items in full or partial set.SM...

    $155.00
  • $365.00

    Designed to adapt a 1.5 Sphere Mount Nest to .5000 Spherically Mounted Retro-Reflector or other spherical type target or accessory.1.5 - .5 SMR AD FEATURES: STAINLESS STEEL Heat-treated and harde...

    $365.00
  • $85.00

    Represents the same centerline and height value as a construction ball. It accepts a Hidden Point Bar (HPB) assembly and is used when it is needed to project 90° to a point that is obstructed from...

    $85.00
  • $527.00

    Provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interchangeability from Laser Tracker systems to Contrast Photogrammetry or Videogrammetry systems.1.5S FEATURES:&n...

    $527.00
  • $39.00

    Supports a spherical mounted Retro-Reflector or other spherical type target or accessory for a critical height and centerline. The edge may be used to contact inside edges to give a value of...

    $39.00
  • $219.00
    Sale!

    NOTE: 10 or more rolls of the same size are eligible for quantity discount. Call for discounted rates. Retro-Reflective tapes are sold in rolls that are 50 yards long....

    $219.00
  • $625.00

    Adapts a 1.5 Spherically Mounted Retro-Reflector to replace the standard optic 3 1/2” diameter line of sight spherical target.LT - LOSA FEATURES: 1144 STEEL, BLACK OXIDE FINISH - Heat-trea...

    $625.00
  • $219.00

    NOTE: 10 or more rolls of the same size are eligible for quantity discount. Call for discounted rates. Retro-Reflective tapes are sold in rolls that are 50 yards long....

    $219.00
  • $625.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating outside corners.1.5 ESM -...

    $625.00
  • $95.00

    Used with the MetricVision measurement systems to represent the centerline of a hole with a zero offset height.FTB FEATURES: STAINLESS STEEL (standard)...

    $95.00
  • $219.00

    NOTE: 10 or more rolls of the same size are eligible for quantity discount. Call for discounted rates. Retro-Reflective tapes are sold in rolls that are 50 yards long....

    $219.00
  • $157.00

    Supports a spherical mounted Retro-Reflector or other spherical type target or accessory for a critical height and centerline. The edge may be used to contact inside edges to give a value of...

    $157.00
  • $527.00

    T1.5S provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interchangeability from Laser Tracker systems to computer-aided Theodolite systems.T1.5S FEATURES: STAINLESS ...

    $527.00
  • $132.50

    Used to adapt standard .2500 shank targets to edges/surfaces by clamping.ETA FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)...

    $132.50
  • $125.00

    Designed to adapt a 1.5 Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory to an Invar Scale Bar.1.5 

    $125.00
  • $275.00

    Designed to hold Spherically Mounted Retro-Reflector or other spherical type target or accessory for the purpose of locating outside corners..5 ESM / OC FEATURES: 1144 STEEL, BLACK OXIDE FIN...

    $275.00
  • $87.00

    Designed for mounting to a surface to securely hold a .8750 diameter, spherically mounted Retro-Reflector or other spherical type target or accessory. The .875 SM-HC is used for reference only; n...

    $87.00
  • $2,460.00

    HUBBS is aware of the nature of your industry. For this reason, we have created the official KIT and CASE that include the most commonly used products. The pelican case enclosing the kit is configured...

    $2,460.00
  • $185.00

    Can be screwed onto the shank end of a Bar Extension to generate a spherical radius while locating the ball at the top edge of a hole.NOTE: BALL IS BONDED TO BASE HANDLE WITH CARE. Balls are on center...

    $185.00
  • $240.00

    Aluminum, Black Anodized Finish (standard)

    $240.00
  • $106.00

    Designed to adapt 90° standard .2500 shank targets to an Invar Scale Bar Kit.ITA-2 FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)...

    $106.00
  • $60.00

    Used for adapting a Hidden Point Bar or Bar Extension to a magnetic base for support.HPBH FEATURES: .375 shaft material: 1144 STEEL, BLACK OXIDE FINISH (standard) Block is plastic....

    $60.00
  • $280.75

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of a hole and 1.000 or 25 mm offset abo...

    $280.75
  • $408.50

    Designed to achieve the centerline of the Leveling Lug.LLST FEATURES: STAINLESS STEEL WITH 1144 STEEL, BLACK OXIDE INSERT - Heat-treated and hardened to R/C 53 - 55 (standard)LLST APPLICAT...

    $408.50
  • $300.00

    Assembles with various Bar Extension lengths and holds the .5 SMR or other spherical type target or accessory on centerline for Hidden Point applications..5 SM / HPBA FEATURES: 1144 STEEL, B...

    $300.00
  • $1,326.50

    HUBBS is aware of the nature of your industry. For this reason, we have created the official KIT and CASE that include the most commonly used products. The pelican case enclosing the kit is configured...

    $1,326.50
  • $85.00

    Used for adapting standard .2500 or .1250 shank targets to threaded holes. (Allow .2000 for height difference)NOTE: .1250 diameter hole, +.0003/-.0000 for major thread diameter .375 and less.2500 diam...

    $85.00
  • $1.00

    Test Product

    $1.00
    Add to cart
  • $0.01

    999PMMG999

    $0.01
    Add to cart
  • $527.00

    Provides same centerline value as a Spherically Mounted RetroReflector. This allows interchangeability from Laser Tracker systems to Total Station systems.TOTAL 1.5S FEATURES:...

    $527.00
  • $83.00

    Used with photogrammetry for locating edges of sheet metal, slots or grooves.NOTE: The side of the target with the flat represents the side of the indexing surface.TSG FEATURES: 1144 STEEL, BLACK OXID...

    $83.00
  • $187.00

    Mounts to a Hidden Point Bar or Bar Extension similiar to the Hard Point. Connects to a Construction Ball and allows for 90° rotation.CBA FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)...

    $187.00
  • $260.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of standard slotted type bushings.1.5 S...

    $260.00
  • $515.00

    Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpse of locating inside corners or radius.N...

    $515.00
  • $125.00

    Holds a 1.5 inch SMR magnetically to a flat, ferrous surface. It can also hold a Theodolite or Photogrammetry Sphere in some orientations.1.5 SMR / MC FEATURES: ALUMINUM BLACK, ANODIZED COATING...

    $125.00
  • $195.00

    Designed to adapt to a 1.5 Sphere Mount Nest in an inaccessible location using .2500 shank applicable accessories.1.5 HPA FEATURES: STAINLESS STEEL WITH 1144 STEEL, BLACK OXIDE INSERT - Heat-tre...

    $195.00
  • $300.00

    Use along with your own shop-provided shank sizes.CPT / INS FEATURES: 1144 STEEL, BLACK OXIDE FINISH - Heat-treated and hardened to R/C 38-42 (standard)...

    $300.00
  • $527.00

    Provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interchangeability from Laser Tracker systems to Photogrammetry or Videogrammetry systems.1.5S FEATURES: HARDENED S...

    $527.00
  • $0.00

    Used with photogrammetry for targeting edges/surfaces.TC / 45 - LH or RH FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless otherwi...

    $0.00
  • $0.00

    Used with photogrammetry for targeting edges/surfaces.TC / 45 NEG or POS FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)NOTE: Target dots are located within +/-.0005 on height (unless o...

    $0.00
  • $205.00

    Used for projecting to a hidden hole or surface. The .2500 hole accepts a 90° target or bar extension. A Starrett 657TW fine adjustment flexible arm magnetic base or equivalent may be used w...

    $205.00
  • $225.00

    Supports a spherical mounted Retro-Reflector or other spherical type target or accessory for a critical height and centerline. The edge may be used to contact inside edges to give a value of...

    $225.00
  • $219.00

    NOTE: 10 or more rolls of the same size are eligible for quantity discount. Call for discounted ratesRetro-Reflective tapes are sold in rolls that are 50 yards long....

    $219.00
  • $402.00

    NOTE: 10 or more rolls of the same size are eligible for quantity discount. Call for discounted rates. Retro-Reflective tapes are sold in rolls that are 50 yards long....

    $402.00
  • $625.00

    Replaces the standard optics 3 1/2” diameter Line of Sight Spherical Target.LOSA FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard) Hardened to R/C 53-55LOSA ORDERING: Specify .3125 or .5000 of...

    $625.00
  • $385.00

    Accepts a target or a sphere mount .500 high, .2500 shank, or .1250 shank in each end to achieve a 3.000 inch offset in each direction. For anything other than a 2.500 length in both directions, pleas...

    $385.00
  • $427.50

    Used to represent the control side of a groove that is in an automotive grid plate at 1.000 or 25mm above and will clear 3mm by 3mm groove or slot.1.5 GLSM FEATURES: 1144 STEEL, BLACK OXIDE FINISH &nd...

    $427.50
  • $155.00

    Designed to tether a 1.5 Spherically Mounted Retro-Reflector to the user or Sphere Mount, preventing loss or damage.NOTE: Full set shown at left, drawings show included items in full or partial set.LE...

    $155.00
  • $150.00

    Mounted to a Theodolite adaptor to hold a .5 Spherically Mounted Retro-Reflector or other spherical type target or accessory in place for a consistant reference point..5 TSM FEATURES: 1144 S...

    $150.00
  • $60.00

    Designed to hold a sphere directly on the surface..5 SMR MC FEATURES: 1144 STEEL, BLACK OXIDE FINISH (standard)...

    $60.00
  • $85.00

    Used with the MetricVision measurement systems to represent the intersection of scribe lines with a zero offset height.SLFTB FEATURES: STAINLESS STEEL (standard)...

    $85.00
  • $527.00

    Provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interchangeability from Laser Tracker systems to Contrast Photogrammetry or Videogrammetry systems.1.5S FEATURES:&n...

    $527.00
  • $440.00

    Holds (2) Tooling Ball Retro-Reflectors or other spherical type target or accessory to measure location and angularity of a hole.

    $440.00
  • $290.00

    Supports a spherical mounted Retro-Reflector or other spherical type target or accessory for a critical height and centerline. The edge may be used to contact inside edges to give a value of...

    $290.00
  • $337.50

    Supports a spherical mounted Retro-Reflector or other spherical type target or accessory for a critical height and centerline. The edge may be used to contact inside edges to give a value of...

    $337.50
Showing 1 - 155 of 155 items
Back to top